Skip to content
Science

Mylar Stacks Could Offer Tough Insulation for Moon Bases

Penn researchers report that stacked Mylar films keep their insulating performance after bending and heavy compression. The material is still at an early laboratory stage.

Moon in 2010
File photo, 2010: Moon. Photo: Gregory H. Revera / Wikimedia Commons, CC BY-SA 3.0

Key points

  • University of Pennsylvania researchers tested stacked Mylar films as possible lunar insulation.
  • The material combines thermal insulation with resistance to bending and compression.
  • Samples survived repeated compression of about 20 megapascals across 10 cycles.
  • Lab samples are about one square centimeter and must be assembled by hand.
  • Researchers say manufacturing at scale remains a challenge.

According to ScienceDaily, researchers at the University of Pennsylvania may have found a practical option for insulating future Moon bases. The team looked at Mylar, a lightweight plastic that is commonly used in food wrap and in reflective emergency blankets when coated with aluminum. The work was published in the journal ACS Applied Materials & Interfaces.

The researchers built a material they call hybrid layered insulating film stacks, or HyLIFS. It is made from hundreds of very thin Mylar sheets arranged in carefully designed stacks. The main goal was to combine two qualities that are hard to achieve together: strong heat insulation and resistance to physical damage.

Why lunar insulation is difficult

Insulation on the Moon must slow heat movement through a vacuum. It must also stay strong enough for daily use, including packing, transport and installation. Many good insulators are fragile, which limits their use in harsh conditions.

Aerogels, for example, are very light and good at keeping heat in. They have been used in industrial pipelines and on NASA’s Mars rovers. Their delicate internal structure, however, can make them easy to damage by impacts or pressure.

Multilayer insulation is another widely used space technology. It uses reflective sheets separated by spacers and works well against radiated heat. It is not designed to carry much weight, and routine contact can tear it.

How the Mylar stacks performed

The team varied how thick each film was. Some samples also received an ultra-thin layer of alumina, the name used for aluminum oxide, which made them more rigid. In a vacuum, the best stacks reached thermal conductivity similar to other advanced vacuum insulation materials. They also stayed flexible.

Compression tests were a key part of the study. The films were squeezed at roughly 20 megapascals. The scientists likened that load to 200 pounds pressing down on a patch no bigger than a fingertip. The stacks survived this load ten times in a row, which surprised the team.

Stacks coated with alumina tolerated the highest compressive stresses the laboratory equipment could apply. Their insulating performance held up during these tests. The researchers say durability did not have to come at the cost of thermal protection.

Hidden heat paths and thin film results

The experiments also pointed to a less obvious factor. Manufacturers add tiny antiblocking particles to plastic films so that thin sheets do not stick together. According to the study, much of the heat moving between sheets passes through the small contact points these particles create in a vacuum.

The results also showed that thinner films do not always insulate better. The thinnest films the team characterized performed similarly to medium-thickness films when coated with alumina. The researchers suspect the particles create extra contact points in thin sheets, which offset the benefit of adding more layers.

Limits before use on the Moon

The researchers stress that the material is far from ready for lunar construction. Current samples measure only about one square centimeter. Each one requires hours of careful cutting and manual stacking, which would be impractical for large-scale production.

Engineers would need new manufacturing methods before the material could protect habitats or spacesuits. The team’s findings do, however, give designers a clearer picture of how heat moves through layered films and how contact points and pressure affect performance.

Frequently asked questions

What material did the researchers test for Moon bases?

The researchers tested Mylar, a lightweight plastic formally called biaxially oriented polyethylene terephthalate. They arranged many thin Mylar sheets into stacks to create a material called HyLIFS.

Why is the Mylar stack material considered promising?

According to the study, the stacks kept their insulating performance after bending and repeated compression. They combined thermal insulation with resistance to physical damage, which the researchers say is difficult to achieve together.

Is the Mylar insulation ready for use on the Moon?

No. The experimental samples are only about one square centimeter and must be stacked by hand, which the researchers say is too slow for large-scale manufacturing.

Sources

This article was written with the help of AI from reports by the outlets listed above. See our Editorial Policy. Spotted a mistake? Tell us.

About the author

Ravi Franklin

Founder & Editor

Ravi Franklin is the founder and editor of Peak Journalism. His background is in graphic design and digital content, and he started Peak Journalism to make global news clear and easy to follow.